What lengths do timber come in

In Canada and the United States, the standard lengths of lumber are 6, 8, 10, 12, 14, 16, 18, 20, 22 and 24 feet (1.8, 2.4, 3.0, 3.7, 4.3, 4.9, 5.5, 6.1, 6.7 and 7.3 m).

What are the standard timber lengths?

Timber is sold in various lengths that are multiples of 30cm (apx a foot). Most common are 1.8m, 2.4m & 3m (apx 6′, 8′ & 10′). Several longer sizes are also sold.

What lengths do 4x2 timbers come in?

4×2 Timber lengths 3.6 metres x 100mm x 47mm. 4.8 metres x 100mm x 47mm. 5.4 metres x 100mm x 47mm. 6.0 metres x 100mm x 47mm.

What lengths is wood sold in?

Standard Timber Lengths Softwood comes in standard lengths of 1.80m 2.10m 2.40m 2.70m 3.0m 3.30m 3.60m 3.90m 4.20m 4.50m 4.80m 5.10m 5.40m 5.70m 6.0m and 6.30m. The Timber Merchant, in general won’t stock the smaller sizes and will prefer to sell the longer lengths.

What are the sizes of construction timber?

a) Log – A trunk with branches off. b) Plank – Pieces 38 mm to 100 mm (1½” to 4″) thick and 150 mm (6″) or over wide. c) Boards – Pieces 10 mm to 38 mm (3/8″ to 1½”) thick and 75 mm (3″) and over wide. d) Battens – Pieces 19 mm to 38 mm (¾” to 1½”) thick and from 25 mm to 75 mm (1″ to 3″) wide.

How much is a length of 2x4?

Now, most timber is milled and planed to give it a little more of a finished look, and a little more of a consistent size and profile. Because of this extra milling, a 2×4 no longer measures a full 2 inches by four inches. Instead, a 2×4 is really only 1 1/2″ by 3 1/2″.

What length do 2x4s come in?

When using studs, other dimensions of 2-by-4 and 2-by-6 lumber is used. Standard lengths for these range from 8 feet up to 16 feet. These lengths are used for wall plating, window and door framing and bracing.

What is a 2x4 wood?

A piece of surfaced (sanded smooth) 2×4 lumber actually measures 1½ inches thick and 3½ inches wide. In rough-cut condition, a 2×4 is slightly less than 2 inches thick and approximately 4 inches wide. When wood is milled from a rough to a smooth surface, it loses about ¼-inch from each of its four sides.

What size is c16 timber?

Nominal sizes (mm)Finished sizes (mm)Lengths (m)47 x 22545 x 2202.4, 3.0, 3.6, 4.2, 4.875 x 10072 x 952.4, 3.0, 3.6, 4.2, 4.875 x 12572 x 1202.4, 3.0, 3.6, 4.2, 4.875 x 15072 x 1452.4, 3.0, 3.6, 4.2, 4.8

What are the measurements of a 4x4?

Nominal SizeActual Size2 x 101 1/2 x 9 1/4 inches (38 x 235 mm)2 x 121 1/2 x 11 1/4 inches (38 x 286 mm)4 x 43 1/2 x 3 1/2 inches (89 x 89 mm)4 x 63 1/2 x 5 1/2 inches (89 x 140 mm)

Article first time published on

What lengths do 2x4 come in UK?

2″x4″ timber is nominally 47mm x 100mm but is “regularised” with 3mm off the thickness and 5mm off the width, so it ends up being around 44mm x 95mm (may be nearer 45mm on the width).

What is a 2x4 in the UK?

I know from reading around that size wise this would roughly equate to the UK’s 44 x 96 and 25 x 44. One weird thing about dimensional lumber is that the size (ex. 2×4) is nominal, meaning that it’s only the approximate size. For example, a 2×4 is actually 1.5″ x 3.5″ (38mm x 89mm) in cross-section.

What is C16 timber?

C16 graded timber kiln dried is mainly used on internal floor joists and roof joists. … C16 treated timber is specified when the strength is required in an outside environment. Treated C16 timber is often found in roof rafters, timber framing, ceiling joists, floor joists and deck joists and other garden buildings.

What is the difference between lumber and timber?

In the US and Canada, timber is typically used to collectively refer to trees—or the wood of such trees—that have yet to be cut or processed, while lumber typically refers to wood that has been processed as a building material (boards and planks).

What size is a 6x6?

Nominal SizeActual Size4x63-1/2″ x 5-1/2″6×65-1/2″ x 5-1/2″

Why are wood dimensions wrong?

The “nominal” cross-section dimensions of a piece of lumber, such as 2 X 4 or 1 X 6, are always somewhat larger than the actual, or dressed, dimensions. The reason is that dressed lumber has been surfaced or planed smooth on four sides (called S4S). The nominal measurement is made before the lumber is surfaced.

What are standard stud lengths?

Two-by-six and two-by-four are the most common dimensions of wall studs. Standard walls of 8 feet have wall studs that are 92 inches. The studs are 104 1/2 inches in homes with 9-foot walls.

What is the actual length of an 8 foot 2x4?

2×4 – 8: 96” Although not quite as common as the pre-cut studs I described above, my local Home Depot has a fairly good selection of 2x4s that measure 8 feet (96”).

How long is a precut stud?

Home Construction Improvement In most areas of the Country framers are using pre-cut studs measuring 92-5/8″, not 96″ long. Pre-cut studs are readily available from lumber yards for both 8′ framing (92-5/8″) and 9′ framing (104-5/8″).

Why do 2x4 have rounded edges?

2×4 have rounded edges as it’s very beneficial to the wood itself and those working with it. They reduce the number of injuries like unwanted splinters during the handling and manufacturing process and also ensure that the lumber stays looking its best all throughout until the customer sees it.

What lengths do 2x6 come in?

• x 6 in. x 8 ft. # 2 and Better Prime Douglas Fir Lumber. …
• x 6 in. x 4 ft. Premium Southern Yellow Pine / Fir Dimensional Lumber. …
• x 6 in. x 10 ft. Construction Common Redwood Lumber. …
• x 6 in. x 8 ft. Construction Common Redwood Dimensional Lumber. …
• x 6 in. x 14 ft. …
• x 6 in. x 8 ft. # …
• x 6 in. x 8 ft. # …
• x 6 in. x 8 ft.

What lengths do timber joists come in?

Size of joist mm400mm600mm50 x 1473.132.6950 x 1703.613.0850 x 1954.133.550 x 2204.643.91

Is C16 timber OK for decking?

Softwood with a strength class rating of C16 is considered the minimum standard for decks above 600mm in height and is a requirement of building regulations for such raised level structures. … For decks below 600mm in height the use of C16 timber is recommended.

Can C16 timber be used outside?

C16 graded CLS timber is better suited to indoor construction such as creating partitioning and internal walls. It is not the best choice for use outside as it might not be able to withstand against severe climate conditions.

What is a 2x6 board?

In North America, the 2×6 size is actually referring to the lumber’s “nominal” dimension. A 2×6’s real or true dimension is 1.5″ x 5.5″ – within the industry it is referred to as its “actual” size. The nominal size is used when discussing lumber nearly 100% of the time! Same for 1×4, 2×4 and 4×4 etc.

What type of wood is used for framing?

hardwood – softwoods such as pine, spruce or douglas fir are flexible and have straighter grain than hardwoods, giving them a leg up in strength and making them a popular choice for framing.

Is there a 3x3 wood?

3 in. T x 3 in. Douglas fir is low maintenance, resistant to decay and insects, and easy to paint and stain. …

Is a 4x4 actually 4 inches?

While it is true that the actual size of a 4 x 4 board is 3 ½ x 3 ½, that is not a deceptive practice in my opinion. It is well known that lumber is sold based on nominal sizes, and the actual size of the boards is smaller than the nominal size.

What is 2x4 timber in MM?

2” x 2” (50 x 50 mm) 2” x 3” (50 x 75 mm)

What's the difference between CLS and C16 timber?

The CLS timber falls into the easy-edge C16 timber. The easy-edge timber is usually graded as standard C16 timber, but it is smoother and machine-finished making it suitable for a wide range of construction jobs. The easy-edge CLS wood timber is widely used in framing.

What is CLS timber?

CLS Timber – “Canadian Lumber Size” or CLS is finished on all sides giving a smaller cross-section than traditional sawn timber. Originating in the Canadian market, hence the name it is mainly used for timber frame home construction and for internal and partition walls.