Can you epoxy over new concrete

Before an epoxy coating is applied to the floor, Jon-Don highly recommends considering the following: New slabs of concrete should be allowed to fully cure for 30-60 days before a coating is applied. If a sealer was previously used on the concrete (if water beads up on the surface), do not use epoxy.

How long does concrete need to cure before epoxy coating?

Standard specifications recommend a minimum 28 day cure period for “green concrete”, before an epoxy floor coating or other resinous system can be applied.

Do I need to prep new concrete for epoxy?

Before Applying Epoxy The absolute first step before applying your epoxy coating, is to prep your floor. It is essential that you clean your floor thoroughly. If you’re working on a concrete base, fill in any cracks or patch areas that need care before you start to clean.

How do you prepare new concrete for epoxy?

Prepping Your Concrete Floor Before you apply any coating, you need a clean, dry floor without debris, moisture, cracks or holes. Give the area a thorough sweep. Clean up any grease stains with a degreaser and a stiff brush. You don’t need to remove all of the discoloration, just the greasy residue.

Can you epoxy over polished concrete?

Epoxy Can be Used on Any Hard Surface As you may have guessed, polished concrete flooring can only be done to concrete. This limits the ability to have the flooring done in your home if you do not have concrete floors. Epoxy, however, can be applied to just about any hard surface, making it ideal for most homes.

How long should concrete cure before removing forms?

Walls and columns can be removed after about 24-48 hours. Slabs, with their props left under them, can typically be removed after 3-4 days. Soffits, with their props left under them, can be removed after one week. Props supporting slabs under 15 feet can be removed after one week.

How do you know if concrete is ready for epoxy?

The concrete will immediately, or at least within a minute, darken as the water absorbs in areas with no contaminants. You would immediately notice whitening or a frosty hue in areas that have silicone-type contaminates. Further, check to see if the water beads up and then takes more than a couple of minutes to absorb.

How do you epoxy a new concrete floor?

Clean and Degrease the Floor. Use a broom and wet-dry vacuum to clean debris from the floor. …
Etch the Concrete. Etch the concrete floor using the etching solution provided in the epoxy coating kit, following the manufacturer’s directions. …
Prepare the Room. …
Mix the Epoxy. …
Apply the Epoxy. …
Let the Garage Floor Dry.

Can you pour epoxy resin over concrete?

Epoxy coatings are normally applied over concrete floors to provide a high-performance, smooth, and durable surface that can last many years and withstand heavy loads.

What happens if you don't etch concrete before epoxy?

In Closing. New concrete must be etched before applying the epoxy. The smooth surface of unaltered concrete won’t bind with other materials, such as epoxy or paint. As a result, epoxy will peel and lift away, failing to adhere to the surface.

Article first time published on

Should I prime concrete before epoxy?

One of the most common questions I get with epoxy floors is if it is necessary to prime the floor before applying the epoxy floor coat. … The right primer will guarantee better adhesion of your floor coats to the substrate. It will give your floor a longer life and will reduce the risk of the coat chipping or breaking.

Can you epoxy over broom finish concrete?

Concrete floors that have a broom finish (also known as brushed concrete) use up more epoxy than plain concrete floors. … If your floor has a curb around it that you intend to coat with epoxy, you also need to buy additional proxy as curbs take up a lot of coating, especially if it’s made of block.

What's better polished concrete or epoxy?

Polished concrete is preferred over epoxy flooring because of its compressive strength, beautiful look, and its’ resistance to most toxic chemicals and substances. Polished concrete flooring is ideal for garages that will not be subjected to harsh chemicals and materials of extreme pH substances.

Is epoxy good for concrete floors?

Concrete floors professionally finished with an epoxy coating are a fantastic choice for those looking for an attractive solution that is durable, low-cost, and, most importantly, safe. Epoxy floors are topped with a specially engineered coating that consists of a hardener and resin.

Is epoxy floor cheaper than polished concrete?

Cost. Applying epoxy resin costs a lot less compared to installing polished concrete. Polished concrete and epoxy are two of the most affordable flooring options in the market. … Since it’s basically applying epoxy resin on existing surfaces, it’s much more cheaper than installing new floors.

How much weight can a 4 inch slab of concrete hold?

Typically we like to limit the weight to about 40 lb/sqft on an unknown 4″ slab. In most cases you can go to 80 lb/sqft in isolated spots, but unless you know roughly what the soil bearing and reinforcing is for that slab you might be looking at cracking.

How long does 4 inches of concrete take to cure?

Your concrete should be solid enough to walk on, without leaving footprints, after anything from 24 to 48 hours. By seven days, your concrete should be cured to at least 70 percent of its full strength.

Can you leave concrete forms on too long?

The forms or “molding” that holds the concrete in place until it dries should be left alone for at least two days to ensure that the concrete is completely dry. If the forms are removed too soon, the concrete can begin to sag, crack and collapse, especially if conditions like temperature affected its strength.

Will epoxy stick to smooth concrete?

Applying the epoxy to smooth concrete. It is essential for the primer and epoxy to be painted over a rough surface for proper adhesion to take place. Use a floor grinder rather than a shot blaster for best results. … Once applied, the epoxy itself will give the floor the smooth look that you expect.

Does vinegar etch concrete?

Etching – Vinegar’s ability to dissolve CaCO3 will dull your marble, travertine, concrete and terrazzo surfaces. It may “clean” the surface but it is also dissolving pits into the finish and effectively dulling it. … This will affect marble, travertine, concrete and concrete terrazzo surfaces.

Can I sand concrete instead of etching?

Yes, you will need to grind in order to remove the sealer at the surface and provide a proper profile for the coating. You cannot acid etch. The reason is that the sealer prevents the acid from reacting with the minerals in the concrete since the concrete is sealed.

How do you know if concrete needs etching?

If the texture is similar to medium-to-rough sandpaper (150 grit is a good guide), you probably don’t need to etch, although it certainly wouldn’t hurt. If the surface is smooth, definitely etch. However, the etching step needs to come after you clean the concrete.

Do I need to seal epoxy?

Delicate objects that may be damaged by epoxy resin such as photographs, should be sealed with an alternate clear coat (i.e. polyurethane or acrylic sealers) to protect them prior to embedding. Once the seal coat has set, additional flood coats up to 1/8” thick may be applied.

How much does it cost to install an epoxy floor?

Professional epoxy flooring installation costs anywhere from $3 to $12 per square foot including materials and labor. Equipment and material alone will cost about $2 to $5 per square foot.

Do you need a primer for epoxy?

An epoxy primer is the foundation of your floor coating system. Without it, your epoxy system will not work as well no matter what type of epoxy you are applying. Epoxy primers are the layer that you will build upon with other base coats and topcoats.

How long does epoxy floor coating last?

Typically, epoxy flooring lasts 2 to 3 years in heavy traffic. Commercial properties—like garages, restaurants, or factory spaces—with lots of daily foot traffic can expect this experience. However, with proper care and maintenance, your epoxy flooring may last much longer.

Can I epoxy my garage floor myself?

Epoxy garage floors are a great DIY project you can do to spruce up your home. Epoxy will make your floors look nice, clean up easily, and give your garage a finished look. … You must spend the time to properly clean and prep your garage. If you do, the end results will be fantastic.

How much does it cost to epoxy a 2 car garage?

An epoxy based concrete coating for a 2-car garage floor will cost between $1,320 and $3,080 with most homeowners spending about $1,711 when professionally applied. The price to coat an existing concrete floor is ranges from $3 to $7 per square foot including labor and materials.

Can you epoxy over pitted concrete?

For larger areas of pitting and spalling, we recommend using a 100% epoxy concrete patch with a sand aggregate. … It does a good job at filling larger holes as well as having the ability to be trowelled out fairly smooth over larger pits and spalling. Once cured, these repairs are actually stronger than the concrete.